|
| |
|
NID POTS Splitter  |
 The
PS-11-I2 POTS Splitter is a passive low-pass filter designed
to provide POTS service in concert with ADSL technology. The
device blocks high frequency (20kHz - >1MHz) energy from
interfering with POTS equipment.
The PS-11-I2 employs a low-pass filter for standard voice-grade
lines. The PS-11-I2 POTS Splitter is unique because of its
convenient mounting location inside the Network Interface
Device (NID). The PS-11- I2 is similar in size to a standard
station protector and mounts on the Telco side inside the
Network Interface Device. The terminal strip allows for easy
installation so the installer can simply connect the existing
premise wiring to the PHONE terminals on the splitter, and
have POTS service up and running within minutes without expensive,
and time-consuming rewiring. ATU-R terminals connect directly
to the ADSL equipment with existing cable. (data-grade cabling
is recommended for new installations.) |
|
| Features and Benefits |
- Compatible with ADSL Coding Schemes
The PS-11-I2 POTS Splitter is compatible with all ADSL coding
schemes
- Meets ANSI T1.413 -1998 & ITU-T G.992.1/.2
The PS-11-I2 Master POTS Splitter is compliant with the
requirements of both ANSI T1.413-1998 Annex E; ITU-T G.992.1/G.992.2
Annex E.2 Type 2 (North America) & G.992.5 (ADSL2+)
- Passive Low Pass Filter
Passive filter design for continuous phone service in the
event of an AC power failure
|
- Unique Footprint
The PS-11-I2 is similar in size to a standard station protector
allowing direct installation into a wide variety of manufactured
Network Interface Devices.
- Convenient Mounting
The PS-11-I2 POTS Splitter is unique because of its convenient
mounting location in the Telco side of the Network Interface
Device.
- Unlimited ADSL Bandwidth
Full bandwidth allocation as compared to a "micro-filter".
|
|
|
 RTM
( Ring Trip Mitigator) POTS Splitter |
 The
PS-11-RTM ( Ring Trip Mitigator) POTS Splitter is a passive
low-pass filter designed to provide POTS service in concert
with ADSL2+ technology. The device blocks high frequency energy
from interfering with POTS equipment.
The PS-11-RTM employs a low-pass filter for standard voice-grade
lines. With emerging technologies such as ADSL2 and ADSL2+
and enhanced services like video, the POTS splitter is an
integral part of the network.
The PS-11-RTM is specifically designed for video over DSL
applications. The unique design of the PS-11-RTM addresses
specific concerns effecting video such as ring-trip problems.
When used in conjunction with our ADSL2+ CO PS-4100 splitter
series, modem resyncing is virtually eliminated. The PS-11-RTM
POTS Splitter is unique because of its convenient mounting
location inside the Network Interface Device (NID). The PS-11-RTM
is similar in size to a standard station protector and mounts
on the Telco side of the Network Interface Device (NID). The
terminal strip allows for easy installation so the installer
can simply connect the existing premise wiring to the PHONE
terminals on the splitter, and have POTS service up and running
within minutes without expensive, and time-consuming rewiring.
ATU-R terminals connect directly to the ADSL equipment with
existing cable. |
|
| Features and Benefits |
- Compatible with ADSL2+
The PS-11-RTM POTS Splitter is compatible with all ADSL
coding schemes
- Video over DSL Applications
The PS-11-RTM is optimized for video over DSL subscribers
of less than 9,000 feet (2745 m). For DSL subscribers on
longer loops use the PS-11-I3
- Passive Low Pass Filter
Passive filter design for continuous phone service in the
event of an AC power failure
|
- Unique Footprint
The PS-11-RTM is designed to so it can be installed into
a wide variety of manufactured Network Interface Devices
- Convenient Mounting
The PS-11-RTM POTS Splitter is unique because of its convenient
mounting location in the Telco side of the Network Interface
Device
- Environmentally Hardened
The PS-11-RTM is environmentally hardened for extreme installation
conditions
|
|
|
|
RTM POTS Splitter for Indoor Customer Premises |
 The
PS-15-RTM ( Ring Trip Mitigator) POTS Splitter is a passive
low-pass filter designed to provide POTS service in concert
with ADSL2+ technology. The device blocks high frequency energy
from interfering with POTS equipment. The PS-15-RTM employs
a low-pass filter for standard voice-grade lines.
With emerging technologies such as ADSL2 and ADSL2+ and enhanced
services like video, the POTS splitter is an integral part
of the net-work.
The PS-15-RTM is specifically designed for video over DSL
applications. The unique design of the PS-15-RTM addresses
specific concerns effecting video such as ring-trip problems.
When used in conjunction with Wilcom's ADSL2+ CO PS-4100 splitter
series, modem re-syncing is virtually eliminated.
The PS-15-RTM is designed to be mounted inside the customer
premises near where the phone service enters the building.
Two types of connection options are supported by the PS-15RTM
splitter; a standard pole terminal block with screws or RJ
jacks. This allows the installer to simply connect the existing
premise wiring to the PHONE jack or associated terminals on
the splitter, and have POTS service up and running within
minutes without expensive and time-consuming rewiring. An
RJ-45 jack or associated terminals connect directly to the
ATU-R/MODEM equipment with data-grade cabling. |
|
| Features and Benefits |
- Compatible with ADSL2+
The PS-15-RTM POTS Splitter is compatible with all ADSL
coding schemes.
- Video over DSL Applications
The PS-15-RTM is optimized for video over DSL subscribers
of less than 9,000 feet (2745 m). For DSL subscribers on
longer loops use the PS-15-I3.
- Passive Low Pass Filter
Passive filter design for continuous phone service in the
event of an AC power failure.
|
- RJ Jacks and Terminal Block
The PS-15-RTM ADSL Master POTS Splitter has both RJ jacks
and screw type terminals for flexible wiring schemes.
- Easily Mounted
The compact Master POTS Splitter can be screwed in place
or two-sided adhesive tape can be used for mounting the
unit to the desired location.
- Unlimited ADSL Bandwidth
Full bandwidth allocation as compared to the "Micro-filters"
on the market today.
|
|
|
| Wall Mount POTS Splitter |
 The
PS-15-I3S POTS Splitter is a passive low-pass filter designed
to provide POTS service in concert with ADSL technology. The
device blocks high frequency (20kHz-1MHz) energy from interfering
with POTS equipment.
The PS-15-I3S employs a low-pass filter for standard voice-grade
lines. The PS-15-I3S is designed to be mounted inside the
customer premises near where the phone service enters the
building.
Two types of connection options are supported by the PS-15-I3S
splitter; a standard 6 pole terminal block with screws or
RJ jacks. This allows the installer to simply connect the
existing premise wiring to the PHONE jack or associated terminals
on the splitter, and have POTS service up and running within
minutes without expensive and time-consuming rewiring. An
RJ-45 jack or associated terminals connect directly to the
ATU-R/MODEM equipment with data-grade cabling. |
|
| Features and Benefits |
- Compatible with ADSL Coding Schemes
The PS-15-I3S ADSL Master POTS Splitter is compatible with
all ADSL coding schemes
- Meets ANSI T1.413 and G.992.1 - E.2
The PS-15-I3S ADSL Master POTS Splitter is fully compliant
with the requirements of ANSI T1.413-1998 Annex E; ITU-T
G.992.1, G.992.2 Annex E.2 Type 2 (North America) &
G992.5 (ADSL2+)
- RJ Jacks and Terminal Block
The PS-15-I3S ADSL Master POTS Splitter has both RJ jacks
and screw type terminals for flexible wiring schemes
|
- Passive Low Pass Filter
Passive circuitry for continuous phone service in the event
of an AC power failure
- Easily Mounted
The compact ADSL Master POTS Splitter can be screwed in
place or two-sided adhesive tape can be used for mounting
the unit to the desired location
- Unlimited ADSL Bandwidth
Full bandwidth allocation as compared to the "Micro-filters"
on the market today
|
|
|
| ETSI
POTS Splitter |
 The
PS-20 is a full ETSI ADSL POTS Splitter designed to provide
POTS service in concert with ADSL technology. The device blocks
high frequency (20kHz-1MHz) energy from interfering with POTS
equipment. The PS-20 employs a low-pass filter for standard
voice-grade lines. The PS-20 is designed to be mounted inside
the customer premises near where the phone service enters
the building.
Connections to the ADSL modem, house phone(s) and telephone
line are via RJ-11 jacks. This allows the installer to simply
connect the existing premise wiring to the PHONE jack on the
splitter, and have POTS service up and running within minutes
without expensive and time-consuming rewiring. An RJ-11 jack
connects directly to the ADSL equipment with data-grade cabling. |
|
| Features and Benefits |
- Compatible with ADSL Coding Schemes
The PS-20 ADSL POTS Splitter is compatible with all ADSL
coding schemes
- Meets ETSI TR 101 728
The PS-20 ADSL POTS Splitter is fully compliant with the
requirements of ETSI TR 101 728 and return loss requirements
of ITU -T G.992.1
|
- Passive Low Pass Filter
Passive circuitry for continuous phone service in the event
of an AC power failure
- Convenient Mounting Clip
The compact mounting clip can be screwed into place, then
the ADSL Splitter easily slides into the clip.
|
|
| |
| ETSI ISDN Splitter |
 The
PS-21 is a full ETSI combined ISDN/POTS ADSL Splitter designed
to provide ISDN service in concert with ADSL technology. The
device blocks high frequency (20kHz-1MHz) energy from interfering
with ISDN/POTS equipment. The PS-21 employs a low-pass filter
for standard voice-grade lines.
The PS-21 is designed to be mounted inside the customer premises
near where the phone service enters the building. Connections
to the ADSL modem, house phone(s) and telephone line are via
RJ-11 jacks. This allows the installer to simply connect the
existing premise wiring to the PHONE jack on the splitter,
and have POTS service up and running within minutes without
expensive and time-consuming rewiring. An RJ-11 jack connects
directly to the ADSL equipment with data-grade cabling. |
| |
| Features and Benefits |
- Compatible with ADSL Coding Schemes
The PS-21 ISDN/ POTS Splitter is compatible with all ADSL
coding schemes
- Meets ETSI TR 101 728
The PS-21 ADSL POTS Splitter is fully compliant with the
requirements of ETSI TR 101 728 and return loss requirements
of ITU -T G.992.1
|
- Passive Low Pass Filter
Passive circuitry for continuous phone service in the event
of an AC power failure
- Convenient Mounting Clip
The compact mounting clip can be screwed into place, then
the ADSL Splitter easily slides into the clip.
|
|
| |
| VDSL2 CPE Master POTS Splitter
|
 The Master Splitter is a passive low-pass
filter designed to provide POTS service in concert with
DSL technology. The device blocks high frequency
(20kHz-30MHz) energy from interfering with POTS
(Plain Old Telephone Servce) equipment. The PS-36
employs a low-pass filter for standard voice-grade copper
lines.
The PS-36 is ideally suited for video over
DSL applications such as IPTV (Internet Protocol Television)
over ADSL2+ or VDSL2. The PS-36 includes
robust ring-trip protection for non-zero cross ringers
to eliminate video artifacts due to pixelization.
The PS-36 is designed to be mounted inside the
customer premises near where the phone service enters
the building. Two types of connection options are supported
by the PS-36 splitter; a standard 6 pole terminal block with screws or RJ jacks. This allows the installer to simply connect the existing premise wiring to the PHONE jack or associated terminals on the splitter, and have POTS
service up and running within minutes without expensive and time-consuming rewiring. An RJ-45 jack or associated
terminals connect directly to the ATU-R/MODEM equipment with data grade cabling. |
| |
| Features and Benefits |
- Compatible Coding Schemes
The PS-36 DSL Master Splitter is compatible with
all ADSL2+ & VDSL2 coding schemes
- Meets ITU-T and ANSI Standards
The PS-36 DSL Master Splitter is fully compliant
with the requirements of ANSI T1.413-1998
Annex E; ITU-T G.992.1, G.992.2 Annex E.2
Type 2 (North America) G992.5 (ADSL2+) &
G.993.2 (VDSL2)
- RJ Jacks and Terminal Block
The PS-36 DSL Master Splitter has both RJ jacks
and screw type terminals for flexible wiring
schemes
|
- Ring Trip Mitigation
The unique design of the PS-36 also
addresses specific concerns during difficult
ringing and ring-trip conditions.
- Easily Mounted
The compact DSL Master Splitter can be screwed
in place or two-sided adhesive tape can be used
for mounting the unit to the desired location
- Increased Bandwidth
Supports connections to 34 MHz for the full
4096 subcarriers and data speeds of 200 Mbps.
|
|
|
