| |
| |
|
| Ridge-It
Anchor |
|
 |
Ridge-It is an easy to
install tie-off point for one worker. New construction
and retrofit installation is a snap.
Ridge-It provides an attachment location on each side
of the roof for one worker only. Two workers cannot
be attached to the same Ridge-It.
Recommended spacing for rooflines is every 10 ft. Ridge-It
must be installed into a truss.
Also available in a D-ring model for vented ridge applications
or ridge caps wider than 12".
| Features: |
| • |
Stainless steel strap with galvanized
D-rings and nails |
| • |
Weather resistant design installs
underneath standard 12" ridge caps, so none
of the fasteners are exposed to the elements after
installation. |
| • |
Easy retrofit installation on existing
shake or shingle roofs. |
| • |
Low profile design makes only the
D-rings visible after installation. |
|
 |
|
|
| |
 Snappy
Disposable Anchor |
|
Snappy anchors provide a safe
tie-off point for temporary work where a permanent anchorage
point is not needed. For wood roof applications, Snappy must
be nailed into a truss.
Snappy is not a permanent anchor point. When task is complete,
Snappy should be bent over and the roofing material installed
directly over the destroyed anchor. Sold in cartons of 8 or
25. Meets 5,000 lb. load rating for fall arrest use.
One worker per Snappy anchor. A deceleration device such
as the VLA-25 (Model
#01310) or S.O.S. Kit (Model
#00720) should be used in conjunction with Snappy anchors. |
Ordering Information |
|
Model # |
Quantity |
|
|
00711 |
8 |
|
|
00710 |
25 |
|
|
|
|
| Trus-T Anchor |
|
 |
Trus-T anchors attach directly
to a truss to provide safe fall arrest tie-off points for
all trades. For use on dimensional lumber 2" x 4"
through 2" x 12", any roof pitch
| Features: |
| • |
Fits any pitch: Bend the Truss-T bracket
to fit any roof pitch. |
| • |
Permanent or disposable: For permanent applications
cut a slot into the sheathing for the tab to protrude.
For disposable applications, hammer over the tab and continue
roofing. |
| • |
Weather resistant design: Trus-T anchors
are available with a 2" stainless tab for permanent
use. |
| • |
Easy to install: Simply bend the
Trus-T over the truss and nail into the sides. No through
bolting to fuss with. |
|
 |
Ordering Information |
|
Model # |
Features |
Qty. Case |
|
|
00410 |
2" Stainless Steel Tab
|
10 |
|
|
|
|
| |
| Temper
Reusable Anchor |
|
Temper anchors are tough, long-lasting,
reusable and fit the pitch of the most difficult roof. Heavy-
duty construction allows the anchors to be installed and removed
at the end of the job. Must be installed over a truss.
Easy to install, Temper anchors provide a fall arrest point
for one worker. |
Ordering Information |
|
Model # |
Features |
|
|
00455
|
Reusable for any pitch |
|
|
|
|
| |
| Skyhook |
|
The Skyhook is a permanent rooftop
fall protection anchor. Skyhook anchors are powder-coated
for a durable, weatherproof finish. A pre-painted metal flashing
is available in a variety of colors if desired.
Applications:
Wood: 3/4" CDX Plywood or better
Metal: 20 ga. or thicker
Concrete: Contact manufacturer
|
|
| |
| Skyhook
Flashing |
 |
Flashing is available in two pre-painted
colors and a pre-primed ready-to-paint finish . Gaskets are
also available and sold seperately.
|
|
